Poulan Pro 961920091 Manual do Proprietário

OWNER'S MANUALMODEL NUMBER:PR271SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the Owne

10TO MOVE FORWARD AND BACKWARD (See Fig. 14)SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive con

11TO ADJUST SKID PLATES (See Fig. 16)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each

12OPERATIONTO START ENGINE • Ensure fuel shut-off valve is in the “OPEN” position.Your snow thrower engine is equipped with both a 120 Volt A.C. elec

13MAINTENANCE Engine oil Pivot points➂ Interlock bossesLUBRICATION CHARTGENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover it

14CLEANINGIMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use

15SERVICE AND ADJUSTMENTSWARNING: To avoid serious injury, beforeperforming any service or ad just ments:1. Be sure the on/off switch is in the OFF po

16SERVICE AND ADJUSTMENTSTO REPLACE BELTSThe auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, t

17SERVICE AND ADJUSTMENTSTO REMOVE WHEELS (See Fig. 23)• Remove the wheel pin and retainer pin and remove wheel from axle.NOTE: To seal punctures or

18STORAGEImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never

19TROUBLESHOOTINGSee appropriate section in manual unless directed to a service center/department.PROBLEM CAUSE CORRECTIONDoes not start 1. Fuel shut

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

20REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1

21REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101) AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

22NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

23NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

24KEY PART NO. NO. DESCRIPTIONREPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All componen

25KEY PART NO. NO. DESCRIPTIONREPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101)CONTROL PANEL / DISCHARGE CHUTENOTE: All component

26REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101) CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches. 1

27NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

28NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

29KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equi

3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac- tured to give best possible dependability an

30NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

31REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101) HANDLESKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S

32REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101) DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT:

33REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101) DRIVEKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S.

34REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: U

35REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1 inch =

36REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1 inch =

37REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1 inch =

38REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101) WHEELSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT:

39NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

4PARTS PACKED SEPARATELY IN CARTONSAFTEY IGNITION KEY (S)(1) LOCKNUT 5/16-18(1) CARRIAGE BOLT 5/16-18 x 5/8(1) LOCKNUT1/4-20(1) NYLONWASHER(1) SHOULDE

40REPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101)DECALSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT:

41KEY PART NO. NO. DESCRIPTIONREPAIR PARTS SNOW THROWER - MODEL PR271 (96192009101)DECALSNOTE: All component dimensions given in U.S.

42ENGINE, LCT COMPLETE ENGINE-585335702KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIO

43ENGINE, LCT COMPLETE ENGINE-585335702KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIO

04.27.16 BD Printed in the U.S.A.

5ASSEMBLY / PRE-OPERATIONRead these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Rea

6ASSEMBLY / PRE-OPERATIONCHECK TIRE PRESSUREThe tires on your snow thrower were overinflated at the fac-tory for shipping purposes. Correct and equal

7OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

8MEETS A.N.S.I. SAFETY REQUIREMENTSOur snow throwers conform to the standards of the American National Standards Institute.FIG. 8OPERATIONDrive speed

9CHOKECONTROLTRUCTIONSOPERATIONTO CONTROL SNOW DISCHARGE (See Fig. 11)WARNING: Snow throwers have ex- posed rotating parts, which can cause severe inj